Skip to content
GearLibrary
Alignment refinement

Alignment geometry

Pick the tonearm and the geometry: we calculate overhang, offset and null points, plot error and distortion across the whole record and compare them with the factory geometry. Then print the 1:1 protractor.

Why the cartridge needs aligning

The underlying problem: the record is cut by a head that moves in a straight line along the radius, while a pivoted tonearm plays it along an arc. So the stylus is perfectly tangent to the groove at only two points on the record, the null points. Everywhere else there is a small angle between the cantilever and the groove: the tracking error, which causes distortion.

The two parameters: overhang is how far the stylus reaches beyond the platter spindle, and offset is the angle by which the cartridge is turned relative to the pivot–stylus line. Together they decide where the two null points fall.

Distortion depends not just on the angular error but on the error divided by the radius. The same error weighs much more in the inner grooves, where the linear speed is lower and the modulation is more compressed.

The three schools differ only in where they put the null points

  • Baerwald (Löfgren A): makes the three distortion peaks equal: at the start of the side, between the two nulls and at the end of the side. It is the most balanced compromise, and no zone is penalised.
  • Löfgren B: minimises the average distortion over the whole side. The nulls are closer together: it sounds better in the middle of the record but worse at the extremes, especially near the end.
  • Stevenson: puts the inner null on the last cut groove. Distortion is lowest at the end of the side, where tracking is most critical, and higher over the rest of the record.

In practice: from one scheme to another the cartridge moves in the headshell by up to a couple of millimetres and turns by about one degree. Stevenson suits records cut right to the end, typical of much classical music. With records that end well before the minimum radius, which is most of them, Baerwald or Löfgren B give a better overall result.

IEC or DIN: which inner radius

The two standards differ only in the inner radius, that is, how close to the label the record is assumed to be cut. The outer radius, 146.05 mm, is the same.

  • IEC: the innermost modulated groove is 60.325 mm from the centre. It is the international reference and the one most manufacturers use.
  • DIN: the German standard allows cutting down to 57.5 mm, almost 3 mm closer to the label.

Why the geometry changes: alignment algorithms optimise distortion over the band between the two radii. With DIN the band extends further inwards and the null points move towards the centre. With Baerwald, for example, they go from about 66.0 and 120.9 mm (IEC) to about 63.1 and 119.2 mm (DIN). With Stevenson the inner null is the inner radius itself, so it drops from 60.325 to 57.5 mm. At the cartridge this means about one millimetre less overhang and a slightly smaller offset.

In practice: DIN better protects the end of records cut very far in, with long sides, at the cost of a little more distortion elsewhere. If the record ends before 60 mm, as most do, that protection is not needed and IEC gives a better overall result. That is why it can be chosen: IEC is the default, DIN is for those with many long-sided pressings.

Tonearm
Geometry

Equal weighted error at the edges and in the middle: the lowest distortion peak.

Protractor: print on A4 landscape at 100 % scale (“Actual size”, not “Fit to page”), then check the ruler and the square. The sheet opens in the print dialog: choose “Save as PDF”.

Pick a tonearm from the catalogue or enter its pivot-to-spindle distance or effective length.

How we calculate

  • Null points: Baerwald and Löfgren A with the closed formula, Löfgren B as the least-squares minimum of the weighted error at equal linear offset, Stevenson with the inner null on the last groove.
  • With a fixed pivot-to-spindle distance: effective length = √(d² + n₁·n₂), offset = arcsin((n₁ + n₂) / 2L), overhang = L − d.
  • Exact tracking error: α(r) = arcsin((r² + L² − d²) / 2rL) − offset; distortion with Löfgren’s formula.
  • Checked against the values published by Bool Audio (211 mm mounting) and Le Son: same nulls, overhang, offset and maximum error to the hundredth.